Muscle cars came from the factory with a high level of performance. However, to those not content with factory performance, one can improve their muscle car’s performance. More power can be coaxed from the engine and/or that power can be harnessed and put into forward motion more efficiently. Either approach will increase your car’s potential.
8 WAYS TO INCREASE ENGINE POWER
Engine power can be increased by good tuning of the fuel mixture, proper ignition timing for the engine and fuel combination you will use, properly adjusted plugs of the correct heat range, a good dual exhaust system, a clean and efficient air intake system to the carb, proper operating carb, and good engine condition. If the engine is to be overhauled, do it exactly like the shop manuals specify. Relatively minor changes in cam selection, fuel mixture, ignition timing and advance, rear end gear ratio, compression ratios, and carb type can provide some performance increase without substantially degrading driveability. However, large changes to any part of this balanced setup will almost always cause a loss in actual measured performance. The advantages to this approach include reasonable cost, noticeably better performance in normal driving, and measurably quicker times at the drag strip.
1. INCREASE DISPLACEMENT
More displacement means more power because you can burn more gas during each revolution of the engine. You can increase displacement by making the cylinders bigger. As displacement is a function of an engine’s bore and stroke, one can either increase the bore (widening the cylinder chamber) or increase the stroke or both. Increasing the bore is usually easier and cheaper.
2. INCREASE THE COMPRESSION RATIO
Increasing the compression ratio produces more power by creating a larger “explosion.” However, the more you compress the air/fuel mixture, the more likely it is to spontaneously burst into flame (prior to the spark plug igniting it). The use of higher octane gasoline prevents this early combustion.
3. STUFF MORE AIR INTO EACH CYLINDER
Increasing the amount of air (and therefore fuel) into a cylinder of a given size, increases the amount of power from the cylinder (in the same way that you would by increasing the size of the cylinder). Turbo chargers and super chargers pressurize the incoming air to effectively cram more air into a cylinder.
4. COOL THE INCOMING AIR
Compressing air raises its temperature. You would like to have the coolest air possible in the cylinder because the hotter the air is the less it will expand when combustion takes place. The most common method is to draw cooler air from outside of the engine compartment, usually through the use of hood scoops. Therefore, “Ram Air” systems generally are design to draw in cooler outside air, rather than truly “ramming” the air into the engine. In addition, many turbo charged and super charged cars have an intercooler which is a special radiator through which the compressed air passes to cool it off before it enters the cylinder.
5. LET AIR COME IN MORE EASILY
As a piston moves down in the intake stroke, air resistance can rob power from the engine. Air resistance can be lessened dramatically by putting two intake valves in each cylinder. Some newer cars are also using polished intake manifolds to eliminate air resistance there. Bigger air filters or more efficient air filters (such as K&N Filters) can also improve air flow.
6. LET EXHAUST EXIT MORE EASILY
If air resistance makes it hard for exhaust to exit a cylinder, it robs the engine of power. Air resistance can be lessened by adding a second exhaust valve to each cylinder (a car with 2 intake and 2 exhaust values has 4 valves per cylinder, which improves performance). If the exhaust pipe is too small or the muffler has a lot of air resistance then this can cause back-pressure which has the same effect. High-performance exhaust systems use headers, big tail pipes and free-flowing mufflers to eliminate back-pressure in the exhaust system. Dual Exhaust systems improve the flow of exhaust by having two exhaust pipes instead of one.
7. MAKE EVERYTHING LIGHTER
Lightweight engine parts help the engine perform better. Most engine parts are made of iron – which is cheap but heavy. Switching to Aluminum parts is a bit more expensive, but can reduce engine weight by up to 100 lbs. In addition to losing weight in the best place (up front and up high), lightweight engine parts results in a more efficient engine. For example, aluminum pistons are more efficient because each time a piston changes direction it uses up energy to stop the travel in one direction and start it in another. The lighter the piston, the less energy it takes.
8. INJECT THE FUEL
Fuel injection allows very precise metering of fuel to each cylinder. This improves performance and fuel economy.
9. KEEP IT IN TUNE
Even the most powerful engine will not perform if it is not properly tuned. Tuning an engine is an art and involves fine-tuning the carbs, distributor, timing belts, and other engine internals to achieve the best performance over the RPM band.
